Home Page
   Articles
       links
About Us    
Traders        
Recipes            
Latest Articles
Reusing gas cylinders
Page Previous  1, 2
 
Post new topic   Reply to topic    Downsizer Forum Index -> Reduce, Reuse, Recycle
Author 
 Message
vegplot



Joined: 19 Apr 2007
Posts: 21301
Location: Bethesda, Gwynedd
PostPosted: Tue May 04, 10 10:35 am    Post subject: Reply with quote
    

Bodrighy wrote:
I saw one of these made into a little stove for a caravan. The valve was taken off and a flue fitted onto it and a hole cut out of the side at the bottom. It worked a treat except that the actual bottle got really hot. Acted like a radiator but needed a guard around it all the time. Perhaps good for an outdoor one though

I have 2 of the 19kg ones that I can't get rid of that I ought to do something with if I can get around to it. All I have is an angle grinder though.
pete


A simple cure for that problem is to encase a smaller cylinder inside a large one with minimal contact between the two. That way the surface temperature is lower and the resulting hot air can be more effectively channelled. It makes the stove heavier though.

A risk issue with home made indoor stoves is that you have to paying very careful attention to design and build quality to avoid the risk of carbon monoxide poisoning or fumes. From an hobbyist point of view I'd avoid building stoves for internal use but reserve their use for well ventilated areas.

 
Hairyloon



Joined: 20 Nov 2008
Posts: 15425
Location: Today I are mostly being in Yorkshire.
PostPosted: Wed May 05, 10 12:02 am    Post subject: Reply with quote
    

tiggy wrote:
it was no good for... burning plastic !


 
vegplot



Joined: 19 Apr 2007
Posts: 21301
Location: Bethesda, Gwynedd
PostPosted: Thu May 20, 10 8:18 pm    Post subject: Reply with quote
    

I'm using the smaller of the two gas cylinders to make the stove. I cut off the base and the carry handle and then cut a hole which will server as the fire door in the base of the tank.



The door will be made from the cut out blank. I'm going to weld a flange around the perimeter to provide a nice finish (the Oz Pig doesn't have this) but I need to get my forge made first so I can fabricate the flange. The door will be fixed with an offset hinge and I'll forge the handle and latch and probably rivet it on rather than weld to add to its overall aesthetic. My cutting skills need improving.



I hit on the idea of using the base to make the feet.



and hopefully when welded it will start to look like...



It's got its rump in the air as the rear legs were cut a little higher than the front. I've since fettled them to the same overall height so the stove will sit level.

Next steps are to cut out the top hole and fabricate a collar to act as a hotplate stand and then make the flue outlet and flue.

 
vegplot



Joined: 19 Apr 2007
Posts: 21301
Location: Bethesda, Gwynedd
PostPosted: Fri May 21, 10 12:12 am    Post subject: Reply with quote
    

Looking at the Oz Pig site for reference this beasty is going to be about twice as big.

 
welsh veg grower



Joined: 23 Jan 2009
Posts: 2030
Location: here today but tomorrow...
PostPosted: Fri May 21, 10 6:31 am    Post subject: Reply with quote
    

wow, looking good.

Careful its not too big you will heat the whole of Anglesey with it.

 
LostinFrance



Joined: 17 Feb 2014
Posts: 9

PostPosted: Fri Jul 04, 14 2:05 pm    Post subject: Reply with quote
    

Any finished product pictures yet vegplot? I'm on with making one of these at present.

 
Nick



Joined: 02 Nov 2004
Posts: 34535
Location: Hereford
PostPosted: Fri Jul 04, 14 2:41 pm    Post subject: Reply with quote
    

Don't rush him.

 
john of wessex



Joined: 18 Jun 2007
Posts: 2130

PostPosted: Fri Jul 04, 14 7:10 pm    Post subject: Reply with quote
    

Somebody I met was talking about using welding gas bottles as tube header drums in a water tube boiler for his steam launch

 
vegplot



Joined: 19 Apr 2007
Posts: 21301
Location: Bethesda, Gwynedd
PostPosted: Fri Jul 04, 14 9:07 pm    Post subject: Reply with quote
    

Too many projects. Too busy working. It's in exactly the same state as the last photo.

 
Post new topic   Reply to topic    Downsizer Forum Index -> Reduce, Reuse, Recycle All times are GMT
Page Previous  1, 2
Page 2 of 2
View Latest Posts View Latest Posts

 

Archive
Powered by php-BB © 2001, 2005 php-BB Group
Style by marsjupiter.com, released under GNU (GNU/GPL) license.
Copyright � 2004 marsjupiter.com